Below are the details of the parts required to populate the 4 PCBs
|
Component |
No of |
Description |
Supplier and Part No |
|
J3, J4 |
2 |
6 pin single row 2.54mm female connector to mezzanine |
Rapid Online Order Code: 01-5723 |
|
J1, J2 |
2 |
6 pin motor connector – angled male. Not used if using JST-SH encoder connector cable and adaptor |
Rapid Online Order Code:22-0795 |
|
J6 |
1 |
2 pin battery connector |
Rapid Online |
|
J7 |
1 |
3 pin on/off right angle slide switch |
Rapid Online Order Code: 78-0566 |
|
D1 |
1 |
SB2100 3A Schottky Diode or 1N5401 3A |
Amazon search for SB2100 Rapid Order Code: 47-3144 |
|
U1 |
1 |
DRV8833 DC Motor Controller 2 x 6 pin breakout board Do not get 2 x 8 pin variant from Polulo |
Amazon or Ali Express search for DRV8833 |
|
U2 |
1 |
L7805CV regulator or L4941BV 5V regulator |
Rapid Order ode:47-3290 Amazon Search for L4941BV |
|
C1 |
1 |
0.22uF Ceramic capacitor or 0.1uF Ceramic capacitor if using L4941BV regulator |
Rapid Online Order Code: 11-3449 Rapid Online Order Code: 11-3442 |
|
C2 |
1 |
0.1uF Ceramic capacitor or 22uF 16V 4x7mm electrolytic capacitor if using L4941BV regulator |
Rapid Online Order Code: 11-3442 Rapid Online Order Code: 11-4110 |
|
C3, C4 |
2 |
100uF 16V 5x7mm electrolytic capacitors |
Rapid Online Order Code: 11-4119 |
|
R1 |
1 |
47K To wake up motor driver from sleep |
Rapid Online Order Code: 62-0410 |
MEZZANINE PCB PARTS
|
Component |
No of |
Description |
Supplier and Part No |
|
J1 |
1 |
16 pin male pins connector to go to sensor board |
Rapid online Order Code: 08-7948 |
|
J3, J4 |
2 |
6 pin single row 2.54mm 20mm extended male headers Break 2 lots of 6 pins from one of these 20 pin ones from Pi Hut |
The Pi Hut part No 103531 |
|
J2 |
1 |
6 pin female 2.54mm connector for breakout or Bluetooth module |
Rapid Online Order Code: 01-5723 |
|
J5 |
1 |
4 pin female 2.54mm connector for breakout for OLED or IR receiver |
Rapid Online Order Code: 01-5835 |
|
U1 mount |
2 |
20 pin female 2.54mm connectors for Pico |
Rapid Online Order Code: 08-7949 |
|
U1 |
1 |
Raspberry Pi Pico any variant. Pico H is cheapest, but can use Pi Pico 2 or Pico WH 2Mb Get version with headers |
Rapid Online Order Code: 75-1230 |
|
SW1, SW2, SW3 |
3 |
Tactile switches 6x6mm 5mm height |
Rapid Online Order Code: 78-3821 |
|
R1, R2 |
2 |
680 ohm LED load resistors |
Rapid Online Order Code: 64-0068 |
|
D1, D2 |
2 |
low current Indicator LEDs |
Red Code: 56-0400, |
|
|
|
|
|
LINE SENSOR PCB PARTS
|
Component |
No of |
Description |
Supplier and Part No |
|
J1 |
1 |
16 pin female socket connector to Mezzanine board |
Rapid Online Order Code: 19-0087 |
|
Q1,Q6 |
2 |
BC337 transistor for LED switching |
Rapid Online Order Code: 50-3113 |
|
Q2, Q3, Q4, Q5 |
4 |
BPW85C 3mm phototransistors |
Farnell Order Code 1045524 or Ali Express |
|
D1, D2, D7 |
3 |
D1, D2, D7 – TLCR5800 line illumination LEDs or Truopto OSHR3131A-NO 3mm 3000mcd for a bigger spot |
Farnell order no 4912445 or Rapid-online Order code: 55-0066 |
|
D4, D5, D6 |
3 |
any low current LEDs for sensing indicators |
Red Order Code: 56-0400, Yellow Order Code: 56-0410 |
|
R1 |
1 |
33 ohm resistor for Power decoupling |
Rapid Online Order Code: 62-0334 |
|
R2, R15 |
2 |
390 ohm resistors for current limit to bases of Q1, Q2 |
Rapid Online Order Code: 62-0360 |
|
R3, R5, R17 |
3 |
10 ohm resistors for Illumination LED load resistors |
Rapid Online Order Code: 62-0326 |
|
R4, R16 |
2 |
10K ohms |
Rapid Online Order Code: 62-0394 |
|
R7, R8. R9, R14 |
4 |
2.2K ohm Phototransistor load resistors |
Rapid Online Order Code: 62-0378 |
|
R10, R11, R12 |
3 |
3 x 680 ohm Sensing indicator load resistors |
Rapid Online Order Code: 64-0068 |
|
C1 |
1 |
100uF 16V 5x7mm electrolytic capacitor for 5V power supply decoupling |
Rapid Online Order Code: 11-4119 |
|
C2 |
1 |
10uF 16V 4x7mm electrolytic capacitor for 3.3V power supply decoupling |
Rapid Online Order Code: 11-4109 |
WALL SENSOR PCB PARTS
|
Component |
No of |
Description |
Supplier and Part No |
|
J1 |
1 |
16 pin female socket connector to mezzanine board |
Rapid Online Order Code: 19-0087 |
|
Q1, Q2 |
2 |
BC337 transistor for LED switching |
Rapid Online Order Code: 50-3113 |
|
LDPD1, RDPD1, FPD1 |
3 |
BPW85C 3mm phototransistors – wall detectors |
Farnell Order Code 1045524 or Ali Express |
|
DLED1, DLED2, FLED1 |
3 |
TLCR5800 narrow beam line illumination LEDs |
Farnell order no 4912445 |
|
D1, D2, D3 |
3 |
any low current LEDs for sensing indicators |
Red Order Code: 56-0400, Yellow Order Code: 56-0410 |
|
R2, R7, R8, R9 |
2 |
33 ohm resistor R2 s for Pwr decoupling 10 ohm for wall Illumination LED load resistors R7,R8,R9 |
Rapid Online Order Code: 62-0334 Order Code: 62-0326 |
|
R1, R3 |
2 |
390 ohm resistors for current limit to bases of Q1, Q2 |
Rapid Online Order Code: 62-0360 |
|
R15 |
1 |
1.8K ohm Front facing phototransistor load resistor |
Rapid Online Order Code: 62-0376 |
|
R4, R6 |
2 |
10K ohm resistors |
Rapid Online Order Code: 62-0394 |
|
R11, R13 |
2 |
2.2K ohm Side facing phototransistor load resistors |
Rapid Online Order Code: 62-0378 |
|
R10, R12, R14 |
3 |
680 ohm Sensing indicator load resistors |
Rapid Online Order Code: 64-0068 |
|
C1, C2 |
2 |
100uF 16V electrolytic capacitor for LED power supply smoothing |
Rapid Onlline Order Code: 11-4119 |
|
|
MECHANICAL PARTS
You will need the following parts to complete the robot:
Two motors, wheels and tyres, mounts to hold the motors in place, optionally encoders, a battery and battery connector, nuts and bolts to hold the motors on place and support the Mezzanine or sensor boards, and two skids to keep the robot level. Below are details of each of these things:
|
Motors |
You need 2 Micro Metal Gearmotors with a gear ratio ideally of around 20:1 (600 rpm) with extended back shafts if you plan to add encoders, or with encoders already included. Polulo do 15:1 or 30:1 (800rpm or 400 rpm) 6V motors with encoders fitted which would be OK |
Polulo or Ebay or AliExpress are good sources |
|
Encoders and encoder cables |
You can add an encoder disk to an extended back shaft micro gear motor. These are sometimes available from Pi Hut but more often now the motors are sold with an encoder fitted You will need two 6 pin 1mm pitch JST-SH cables to connect the motor encoder to the main board. An adaptor is used to convert the JST-SH cable to 2.54 pitch to connect it to J1 and J2 |
Cable – Pi Hut “JST-SH cable – 6 pin” Adaptor – Pi Hut “Breakout for 6-pin JST SH-Style Connector – Side Entry” |
|
Wheels and Tyres |
Pololu Wheel 32×7mm Pair available in black or white or you could 3D print some and use O rings for tyres |
Pi Hut SKU: POL-1087 or SKU: POL-1088 |
|
Motor Mounts |
You need 2 motor mounts. They can be 3D printed if you have the capability or you can buy the Polulo ones |
Pi Hut code SKU: POL-989 |
|
Battery and connector |
The battery should be a PP3 9Volt block Lithium Ion rechargeable one with micro USB charging socket and ideally charge level LEDs on the side. The battery Connector lead is from Rapid |
Search on Ebay or elsewhere for “PP3 Block Li-ion USB rechargeable battery” Ideally 1200mAH capacity or similar Standard PP3 9V batteries will not deliver enough current. Rapid Online Order Code: 18-0092 |
|
Nuts and bolts |
If you are using 3D printed mounts which have 3mm holes in them you need 4 M3 x 30mm flat head polyamide bolts. Pack of M3 polyamide nuts 8 required M3 x 10mm plastic spacers or 10mm piece of plastic tubing |
Rapid Online Order Code: 51-3852 Rapid-Online Order Code: 51-3437 |
|
Skids |
A 12mm long M3 bolt and 2 nuts will work for the front skid |
Rapid Online Order Code: 33-7036 |
|
|
|
|
PCBs – You can obtain one free set of boards when you join UKMARS, or for schools we may be able to supply some more. If you want to get your own boards made look at this page https://ukmars.org/projects/gemini/ for details of how to download the Gerber files you will need to provide to your PCB manufacturer |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
